概述:在設備實際操作運行過程中,自動攪拌車的變速器是一個非常重要的部件。因此,我們在使用過程中對其油質需要有一定的檢測工作,那么我們具體
在設備實際操作運行過程中,
自動攪拌車的變速器是一個非常重要的部件。因此,我們在使用過程中對其油質需要有一定的檢測工作,那么我們具體應該怎么進行操作呢?下面小編為您講解。
During the actual operation of the equipment, the transmission of the automatic mixer is a very important component. Therefore, we need to have some inspection work on the oil quality during the use, so how should we operate? The following section explains it for you.
1、將自動攪拌車停放在水平地面上,并拉緊手制動。
1. Park the automatic mixer on the level ground and tighten the hand brake.
2、讓發動機怠速運轉數分鐘。
2. Allow the engine to idle for a few minutes.
3、踩住制動踏板,將操縱手柄撥倒擋、前進擋等位置,并在每個擋位上停留幾秒鐘,使液力變矩器和所有換擋執行元件中都充滿液壓油。后將操縱手柄撥停車擋位置。
3. Step on the brake pedal, move the joystick to reverse gear, forward gear, etc., and stay in each gear for a few seconds to make the hydraulic torque converter and all shift actuating elements full of hydraulic oil. Then, turn the joystick to the parking position.
4、從加油管內撥出自動變速器油尺,將擦干凈的油尺全部插入加油管再拔出,檢查油尺上的油面高度。
4. Pull out the automatic transmission oil dipstick from the oil filler pipe, insert the cleaned oil dipstick into the oil filler pipe and then pull it out, and check the oil level on the oil dipstick.
一般攪拌車自動變速器油的油位檢查可以通過油尺來查看,檢查油位的正確步驟是:
Generally, the oil level of the automatic transmission oil of the mixer can be checked through the dipstick. The correct steps for checking the oil level are:
①行駛被檢車輛,使發動機和變速器達到正常工作溫度(50一90℃);
① Drive the inspected vehicle to make the engine and transmission reach normal operating temperature (50-90 ℃);
②將車輛停放于水平路面,采取駐車制動,將換擋手柄推N位后啟動發動機;
② Park the vehicle on a level road, apply the parking brake, push the gear shift handle to the N position and start the engine;
③使發動機保持怠速運轉,將操縱手柄依次推人所有位置,并在每一個位置上停留片刻,后將手柄推P位;
③ Keep the engine running at idle speed, push the operating handle to all positions in turn, stay at each position for a moment, and then push the handle to position P;
④從自動變速器加油管中拉出油尺,用干凈的紙或布擦拭干凈后再將油尺放回套管,注意油尺插人要到位;
④ Pull out the oil dipstick from the oil filler pipe of the automatic transmission, wipe it with clean paper or cloth, and then put the oil dipstick back into the sleeve. Note that the oil dipstick must be inserted in place;
⑤拉出油尺檢查油位是否在正確位置,液面過高或過低都不允許。
⑤ Pull out the dipstick to check whether the oil level is at the correct position. It is not allowed to have too high or too low liquid level.
在對自動攪拌車變速器進行檢查或故障診斷前,先要對變速器油面和油質進行檢查。把選擋手柄放在P位,將發動機在怠速時少運轉數分鐘,油液達到正常工作溫度,攪拌車須停放在水平路面上,這樣才能確保在差速器和變速器之間的油面高度正常、穩定。
Before the inspection or fault diagnosis of the automatic mixer truck transmission, check the transmission oil level and quality. Put the gear selection handle at P position, and run the engine at idle speed for at least a few minutes. The oil reaches the normal operating temperature. The mixer must be parked on a level road, so as to ensure that the oil level between the differential and the transmission is normal and stable.
自動攪拌車變速器油質的檢測方式就講解到這里了,您對此有什么想咨詢的問題或者有什么需求可以隨時來我們網站
http://kitchinit.com了解!
This is the end of the inspection method for the transmission oil quality of the automatic mixer. If you have any questions or needs, you can come to our website at any time http://kitchinit.com Understand!