取力裝置也是自動攪拌車不可缺少的配件，那么取力器有哪些注意事項，以及在發生故障時大家都知道如何排除故障？以下中科聚峰為大家簡單介紹幾種方法，希望對大家有幫助。

安裝在變速器下方或側面的取力器內腔與變速器相通，無須單獨加潤滑油；但裝在變速器前部或后蓋殼體左上或右上角的取力器內腔與變速器不相通時，應單獨加潤滑油。為避免因磨合而產生的雜質，每隔五百小時更換一次潤滑油的取力器應縮短換油周期，以后每五百小時更換新油，以防潤滑油變質。新加裝取力器的變速器組件應適當縮短換油周期，以避免取力器早期磨損。
The power take-up cavity installed under or on the side of the transmission is connected with the transmission without adding lubricating oil. However, when the power take-up cavity installed at the front part of the transmission or the upper left or right corner of the rear cover housing is not connected with the transmission, oil should be added separately. In order to avoid the impurities caused by running-in, the power take-off device for replacing the lubricating oil every 500 hours should shorten the oil replacement cycle, and then every 500 hours to replace the new oil to prevent deterioration of the lubricating oil. The transmission component of the newly installed power take-off device should be properly shortened in oil change cycle to avoid early wear of the power take-off device.

泄漏

1.檢查漏油部位的油封或內襯是否完好，如果損壞應及時更換。
1. Check whether the oil seal or liner is in good condition and replace it if it is damaged. 

2.檢查結合面涂膠部位，如有局部涂抹不勻，應清理干凈再涂膠。

取力裝置在自動攪拌車上無法上檔或取下檔
The power take-off device can not be put into or taken out of gear on the automatic mixer

1.檢查氣道泄漏情況。
1. Check for leaks in your airways.

2.檢查拔片定位螺絲是否松開或擰斷。
2. Check that the TAB positioning screws are loose or broken.

3.檢查活塞定位螺絲是否松動。
3. Check that the piston positioning screw is loose.

4.檢查拔出的套叉槽是否被拔出。
4. Check that the pull-out fork slot has been pulled out.

5.檢查支承彈簧是否損壞，失效。
5. Check the supporting spring for damage and failure.

6.檢查回位彈簧是否變形，失效。
6. Check the return spring for deformation and failure.

7.檢查指示燈開關是否與活塞干涉。

8.根據上述檢查，更換零部件或采取相應措施。
8. According to the above inspection, replace the parts or take corresponding measures.

反常響聲

1.齒輪有嚴重的磨損或斷齒，需要更換。
1. Gears are severely worn or broken and need to be replaced.

2.軸承有嚴重的磨損、滾針、滾子損壞，必須更換。
2. Bearing has serious wear, needle roller, roller damage, must be replaced.

3.空心軸牙栓松動或損壞，需要重新固定或更換。
3. The hollow axle tooth pin is loose or damaged and needs to be re-fixed or replaced.

自動攪拌車取力器顯示器開關失靈

1.指示燈開關接線柱損壞，需要更換。
1. The indicator lamp switch terminal is damaged and needs to be replaced. 

2.指示燈開關安裝位置不對，導致頂桿頂不上觸頭或經常接觸，可以加墊墊或撤墊處理。
2. The indicator light switch is not installed in the right position, resulting in the ejector rod top contact or frequent contact, can add or remove the pad pad to deal with.

3.指示燈開關，頂桿變形，需要更換。

3. Indicator light switch, ejector pin out of shape, need to be replaced.