RM新时代入口

歡迎來到中科聚峰機械有限公司!

24小時服務熱線:

400-879-1999

點擊撥打服務熱線:400-879-1999
當前位置:首頁>新聞中心>公司動態自動上料攪拌車發動機損壞是什么原因?

自動上料攪拌車發動機損壞是什么原因?

來源:http://kitchinit.com/ 日期:2021-03-01 發布人:admin
概述:自動上料攪拌車經過長時間使用之后就會發生一些情況,這些情況有大有小,小的毛病不會有什么大的影響,但是大的情況就有可能會損害自動上料攪拌車,今天為大家介紹一下發動機損壞是什
自動上料攪拌車經過長時間使用之后就會發生一些情況,這些情況有大有小,小的毛病不會有什么大的影響,但是大的情況就有可能會損害自動上料攪拌車,今天為大家介紹一下發動機損壞是什么原因。
Automatic feeding mixer after a long time of use, there will be some situations, these situations have big and small, small problems will not have a big impact, but big situation may damage the automatic feeding mixer, today I will introduce the cause of engine damage.
1、氣門腳空地的調整:配氣安排各機件在正常運用中,跟著零件的磨損,氣門腳空地將發生改動。如凸輪、氣門桿端面及挺桿接觸面磨損后空地將變大,而氣門頭與氣門座磨損后空地又變小,因此,在調整中應取空地的基地值為宜。如規矩為0.2~0.25mm,可實取0.22mm,這么既照顧了空地改動的實際情況,又思考了測量誤差疑問,可充沛保證氣門腳空地效果的完成。
1. Adjustment of valve foot clearance: valve arrangement in normal operation, with the wear of parts, valve foot clearance will be changed. If the cam, valve stem end face and tappet contact surface are worn, the open space will become larger, and the open space will become smaller after the valve head and valve seat are worn. Therefore, the base value of the open space should be taken in the adjustment. If the rule is 0.2 ~ 0.25 mm, the actual value can be 0.22 mm, which not only takes care of the actual situation of the air space change, but also considers the measurement error question, which can fully ensure the completion of the air space effect of the valve foot.
2、氣門座的鉸削:氣門座鉸削通常為手作業業,應格外重視三個疑問:一是在凹陷、斑駁,能鉸出無缺錐面的基礎上,鉸削量越小越好;二是鉸削時用力要均勻,起刀收刀要輕,少鉸多調查,以保證較少的鉸削量和較高的光潔度;三是與氣門試配,判定好作業面方位和寬度。
2. Valve seat reaming: valve seat reaming is usually manual operation, so we should pay special attention to three questions: first, on the basis of eliminating depression and mottling and being able to ream out the intact cone surface, the smaller the reaming amount is, the better; second, the force should be uniform when reaming, and the cutter should be light when starting and closing, and more investigation should be carried out with less reaming to ensure less reaming amount and higher finish; Third, try to match with the valve to determine the orientation and width of the working face.
方位應調整到氣門錐面的中下部,偏上或偏下可用上、下口鉸刀進行調整。作業面寬度,進氣門可掌握在0.9mm(規矩為1~2.2mm),排氣門可掌握在1.4mm(規矩為1.5~2.5mm)。實踐證明上述寬度在氣門與氣門座研磨后,進氣門可達1mm,排氣門可達1.5mm,均在規矩寬度的下限,能大大提高其運用壽數。
The position should be adjusted to the middle and lower part of the valve cone. The upper and lower reamers can be used to adjust the position. The width of working face can be controlled within 0.9mm (1 ~ 2.2mm) for intake valve and 1.4mm (1.5 ~ 2.5mm) for exhaust valve. Practice has proved that the width of the intake valve and the exhaust valve can reach 1 mm and 1.5 mm after grinding the valve and valve seat, which are all in the lower limit of the regular width and can greatly improve the service life.
3、攪拌車修補質量差在修補作業中出色的疑問是氣門與氣門座作業面加工質量達不到懇求,構成作業面燒蝕、凹陷而前期損壞;凸輪軸軸承在刮削中其協作空地、接觸面積、各軸承同心度達不到懇求,加速磨損,呈現異響構成前期損壞;氣門導管在更換新件時,鉸削質量達不到規矩懇求,直接影響氣門及氣門座運用壽數。
3. The problems of poor repair quality of mixer truck in repair operation are that the machining quality of valve and valve seat working surface can not meet the requirements, which results in ablation and depression of working surface and early damage; the clearance, contact area and concentricity of camshaft bearing can not meet the requirements in scraping, which accelerates wear and presents abnormal sound, which results in early damage; when the valve guide is replaced with new parts, the hinge is broken The cutting quality can not reach the standard, which directly affects the service life of valve and valve seat.
自動上料攪拌車
Automatic feeding mixer
4、凸輪軸軸承的刮削:凸輪軸軸承的刮削歸于手作業業,保證質量有一定難度。為刮削便利,又通常在氣缸體外加工,因此應格外留意四個疑問:一是要判定好軸承刮削后內孔的直徑;二是刮削中要盡量留意堅持軸承內孔與外圓的同軸度;三是邊刮削邊與軸頸試配,并保證接觸印痕分布均勻;四是將軸承壓入座孔時,應留意對正油孔。刮削后裝入凸輪軸,翻滾數圈,視情進行恰當修整,接觸面積應抵達75%以上并分布均勻,空地符合規矩。
4. Scraping of camshaft bearing: scraping of camshaft bearing belongs to manual operation, so it is difficult to ensure the quality. For the convenience of scraping, it is usually processed outside the cylinder body, so we should pay special attention to four questions: first, we should determine the diameter of the bearing inner hole after scraping; second, we should pay attention to the coaxiality of the bearing inner hole and the outer circle during scraping; third, we should try to match with the journal while scraping, and ensure that the contact marks are evenly distributed; fourth, we should pay attention to aligning the oil hole when pressing the bearing into the seat hole. After scraping, install the camshaft, roll for several circles, and properly trim according to the situation. The contact area should reach more than 75% and be evenly distributed, and the open space should conform to the rules.

截屏,微信識別二維碼

RM新时代入口