As long as the user has certain professional maintenance knowledge, it will be of great help in use. But mechanical oil leakage is a very common problem, but today to teach you these moves, automatic feeding mixer "stop oil" has these 8 points is enough!

使用時間過長且油封是正常磨損情況。方案：更換新的油封即可。

The service time is too long and the oil seal is normal wear condition. Solution: replace the oil seal with a new one.

油長期未更換、濾芯質量不合格，油品過臟，從而加快了油封磨損情況。方案：盡快更換液壓油、濾芯。

The oil has not been replaced for a long time, the quality of the filter element is not up to standard, and the oil is too dirty, thus speeding up the wear of the oil seal. Solution: replace hydraulic oil and filter element as soon as possible.

傳動軸平衡失效，擺動量大，從而引起了主軸擺動油封偏磨。處理方案：及時糾正、更換轉動軸。

The balance of the transmission shaft fails and the swing momentum is large, which causes the eccentric wear of the oil seal of the spindle swing. Treatment plan: correct and replace the rotating shaft in time.

液壓油變質、乳化，從而導致潤滑性能下降，加快了油封磨損情況。方案：盡快更換液壓油、濾芯，嚴重時需要清理系統。

The deterioration and emulsification of hydraulic oil result in the decrease of lubricating performance and the acceleration of oil seal wear. Solution: replace the hydraulic oil and filter element as soon as possible, and clean the system if it is serious.

泵支架松動、開泵、泵固定螺栓松動，進而引起液壓泵出現整體抖動情況且油封出現磨損現象。方案：經常檢查并排除自動上料攪拌車中可能出現的故障，預防并避免故障的發生。

The pump bracket is loose, the pump is opened, and the pump fixing bolt is loose, which causes the overall shaking of the hydraulic pump and the wear of the oil seal. Solution: frequently check and eliminate the possible faults in the automatic feeding mixer, and prevent and avoid the occurrence of faults.

自動上料攪拌車系統的回油不通暢，回油管、散熱器發生堵塞，進而導致馬達殼中壓力增加，引起油封出現漏油情況。方案：排除堵塞并保持回油循壞保持通暢。

The oil return of the automatic feeding mixer system is not smooth, and the oil return pipe and radiator are blocked, which leads to the increase of pressure in the motor housing and the oil seal leakage. Solution: remove the blockage and keep the return oil circulation unobstructed.
 

散熱器不散熱導致油溫過高，粘度、潤滑性下降，油封過熱密封失效等問題的出現。方案：排除散熱器故障，為系統進行降溫過程，避免泵馬達磨損。嚴重時還要停車熄火，用水沖泵馬達、散熱器殼體達到降溫效果。

The radiator does not dissipate heat, which results in the oil temperature being too high, the viscosity and lubricity decreasing, the oil seal overheating and sealing failure. Solution: eliminate the radiator failure, cooling the system to avoid pump motor wear. In serious cases, the engine should be shut down and the pump motor and radiator shell should be flushed with water to achieve cooling effect.

冬季起車時若預熱不足，導致油溫過低，油液、油封未達到理想工作溫度。處理方案：在起車時停罐怠速運轉10min20min，待油溫正常后再轉罐工作。

In winter, if the preheating is insufficient, the oil temperature is too low and the oil and oil seal do not reach the ideal working temperature. Treatment plan: stop the tank at idle speed for 10min to 20min when starting, and then turn the tank to work after the oil temperature is normal.

自動上料攪拌車的液壓泵軸端油封屬于易損件，若嚴格按照相關規范進行操作，其實很多漏油現象都會得到有效預防，若出現漏油問題，要冷靜查找具體原因并進行處理即可。

The oil seal at the shaft end of the hydraulic pump of the automatic feeding mixer is a vulnerable part. If the operation is carried out in strict accordance with the relevant specifications, in fact, many oil leakage phenomena will be effectively prevented. In case of oil leakage, it is necessary to find out the specific causes and deal with them calmly.