Even if the mechanical equipment is used for a long time, it needs to be refueled from time to time to maintain good operation performance. So what should be paid attention to when adding lubricant to the equipment?

1.在操作過程中，請勿對攪拌一體車進行大修和潤滑。

1. Do not overhaul or lubricate the automatic feeding mixer during operation.

2.定期在每個注油嘴中注滿潤滑脂，每4小時向軸端密封圈涂抹潤滑脂，并每周排放一次污水。

2. Fill grease in each nozzle regularly, apply grease to shaft end sealing ring every 4 hours, and discharge sewage once a week.

3.使用自動供料攪拌器后，根據需要在每個潤滑點添加所需的潤滑油（輥軸，輥，鋼絲繩和其他運動部件）。

3. After using the automatic feeding agitator, add the required lubricating oil (roller shaft, roller, wire rope and other moving parts) at each lubricating point as required.

4.攪拌一體車減速器齒輪箱中的齒輪和軸承利用齒輪旋轉將油撒到箱體的內壁上，并流入軸承中進行潤滑。變速箱中的油位應保持在油尺上的兩條刻線之間。如果油位過高或過低，每個零件的溫度都會升高，潤滑會不足，從而導致功率損耗增加，機器運行速度變慢。

4. The gear and bearing in the gearbox of the mixer truck use the gear rotation to scatter the oil on the inner wall of the gearbox and flow into the bearing for lubrication. The oil level in the transmission should be maintained between the two lines on the dipstick. If the oil level is too high or too low, the temperature of each part will rise and the lubrication will be insufficient, which will increase the power loss and slow down the running speed of the machine.

5.為自動供料混合器選擇的潤滑油必須不含比粘度和粘度-溫度特性，低凝固點，良好的氧化穩定性，機械雜質和水分以及腐蝕和磨蝕性物質。其質量指標必須符合標準。

5. The lubricating oil selected for the automatic feed mixer must be free of specific viscosity and viscosity temperature characteristics, low freezing point, good oxidation stability, mechanical impurities and moisture, and corrosive and abrasive substances. Its quality index must conform to the national standard.

潤滑自動進料混合器可有效減少磨損并延長組件壽命。但是，在添加潤滑油的過程中需要注意一些事項，在新機器的前150個小時和300個小時應更換一次潤滑油，以去除在測試運行期間未完全清潔的污垢。在工作期間，應經常檢查油位以彌補時間不足。

Lubrication of the automatic feed mixer can effectively reduce wear and prolong the service life of the components. However, in the process of adding lubricating oil, it is necessary to pay attention to some matters. In the first 150 hours and 300 hours of the new machine, the lubricating oil should be replaced to remove the dirt that is not completely cleaned during the test run. During the working period, the oil level should be checked frequently to make up for the lack of time.

攪拌一體車添加潤滑油的注意事項，希望對您有幫助！如想要了解更多的精彩內容請關注：http://kitchinit.com會有為大家呈現更多的精彩內容。

Notice of adding lubricating oil to mixer truck, hope to help you! For more details, please pay attention to: http://kitchinit.com There will be more wonderful content for you.