1. When removing the tire, stop in a clean, flat, dry, hard and oil-free air to avoid sand, debris, etc. falling on the inner wall of the outer tire or adhering to the outer surface of the inner tire to damage the inner tire, and avoid oil adhering to the tire and corroding the tire.

2、拆卸輪胎應由有實踐經歷的人員操作或指導，切不可亂敲亂打，以免使輪圈產生銳邊、凹痕、龜裂等缺陷，并要堅持輪圈的清潔，避免銹蝕損壞。

2. The removal of tires shall be operated or guided by personnel with practical experience. It is not allowed to knock or beat randomly, so as to avoid sharp edges, dents, cracks and other defects of the rim, and the rim shall be kept clean to avoid corrosion and damage.

3、只能運用專用工具和撬棒停止拆裝，停止運用螺絲刀之類的鋒利工具。

3. Only use special tools and crowbars to stop disassembly and assembly, and stop using sharp tools such as screwdrivers.

4、拆卸辦法。放掉輪胎中的空氣，應用氣門帽將氣門芯擰出，打下氣門嘴固定螺母，用雙腳踩踏或用錘子重?fù)敉馓?cè)面，使輪胎的胎圈脫離輪圈邊緣進入輪輞中部凹槽內，將氣門嘴推進輪圈內。在氣門嘴左近將撬棒插入胎緣輪輞之間，將胎緣撬起。

4. Disassembly method. Release the air in the tire, screw out the valve core with the valve cap, knock down the valve fixing nut, tread with both feet or hit the side of the outer tire with a hammer to make the tire bead separate from the rim edge and enter the groove in the middle of the rim, and push the valve into the rim. Insert a pry bar near the valve into the tire rim and pry up the tire rim.

同時在撬胎棒的對面用力緊縮外胎胎壁，使外胎盡量移向輪輞中部凹槽內，行將撬出的部位盡量放松。然后將二根撬胎棒插入一根撬胎棒左近，順著輪輞逐步地將胎緣撬出，尚未撬出的局部，應盡量壓向輪輞直徑小的凹槽部。當輪胎的一邊被撬出后，便很容易地取出內胎及外胎另一邊。

At the same time, tighten the outer tire wall on the opposite side of the tire prying rod to move the outer tire to the groove in the middle of the rim as much as possible, and relax the part to be pried out as much as possible. Then insert two tire prying rods to the left of one tire prying rod, and gradually pry out the tire rim along the rim. The parts that have not been pryed out shall be pressed to the groove with small rim diameter as far as possible. When one side of the tire is pried out, it is easy to take out the inner tire and the other side of the outer tire.

5、假如攪拌車輪胎運用日久，外胎銹死在輞圈內而不容易取下時，能夠?qū)⑤喬テ椒旁跐崈舻目罩猩?，用撬棒在胎口與輞圈之間撬開一定間隙，在輞圈與外胎的分離部倒些肥皂水或清水，并用鐵錘沿l輪圈外側稍加錘擊，使水在振動的過程中從縫隙處滲入生銹面，待浸透后（約2～3min），外胎便容易拆下來。

5. If the mixer tire is used for a long time and the outer tire is rusted in the rim ring and is not easy to remove, the tire can be placed flat in the clean air, pry a certain gap between the tire orifice and the rim ring with a crowbar, pour some soapy water or clean water at the separation part between the rim ring and the outer tire, and hammer slightly along the outside of the L rim with a hammer to make the water penetrate into the rusty surface from the gap during vibration, After soaking (about 2-3 minutes), the outer tube can be easily removed.

閱讀了本篇文章你是否對全自動上料攪拌一體車的輪胎的拆卸方法有了一定的了解了呢？希望本篇文章能對你有所幫助。

After reading this article, do you have a certain understanding of the disassembly method of the tire of the fully automatic feeding and mixing integrated vehicle? I hope this article can help you.