If the automatic feeding mixer is not cleaned in time or not cleaned in place, it will lock up if it is not cleaned for a long time. So what problems often occur in automatic loading mixer? How to repair the problem? Let's follow Xiaobian to have a look

一.行走無力或油溫過高

1、 Weak walking or high oil temperature

自動上料攪拌車行走無力或油溫過高時，就需要判別是離合器活塞密封不嚴仍是油壓缺乏引起的，但慣例檢測手段有時很難斷定是哪個原因引起毛病，尤其是在無動力的情況下，檢查組裝

When the automatic feeding mixer truck is unable to walk or the oil temperature is too high, it is necessary to judge whether it is caused by the loose sealing of the clutch piston or the lack of oil pressure, but it is sometimes difficult to determine which cause the problem by conventional detection methods, especially when there is no power, check the assembly

好的變速器總成的各密封環就更困難了。此刻，可采用氣壓閥進行測試。

Good sealing rings of the transmission assembly are even more difficult. At this point, the pneumatic valve can be used for testing.

1.將自動上料攪拌車變速器控制閥拆掉（對組裝好的變速器應在裝控制閥之前）；

1. Remove the control valve of the transmission of the automatic feeding mixer (for the assembled transmission, it shall be before installing the control valve);

2.順次給變速器各油孔通人0.6一0.8MPa的氣體，若某一個孔通人氣體時，聽到"嘭"的一聲且無漏氣聲或漏氣聲很小進口計量泵，則闡明與之對應的離合器活塞與缸筒間的密封杰出；

2. Successively fill each oil hole of the transmission with 0.6-0.8mpa gas. If a "bang" sound is heard when a hole is filled with gas, and there is no air leakage sound or the air leakage sound is very small, the corresponding sealing between the clutch piston and the cylinder barrel shall be clarified;

3.若聽不到活塞壓緊摩擦片的動靜且漏氣聲較大，則闡明離合器活塞與缸筒間的密封失效，應替換密封件。

3. If you can't hear the movement of the piston pressing the friction plate and the sound of air leakage is large, it indicates that the seal between the clutch piston and the cylinder barrel is invalid and the seal should be replaced.

二.自動上料拌和機抱軸

2、 Shaft holding of automatic feeding mixer

1.可能是拌和主機進水管與沖水方位原因。沖水點方位和沖刷方向不正確的話，也或者是沖水壓力過低，導致水在進入主機內部后，不能將暫時粘結在軸上的混凝土沖刷掉，則時刻久了就簡單構成抱軸。

1. It may be caused by the water inlet pipe and flushing direction of the mixing machine. If the flushing point orientation and flushing direction are incorrect, or the flushing pressure is too low, so that the water can not wash off the concrete temporarily bonded to the shaft after entering the main engine, it will simply form the shaft holding after a long time.

2.可能是質料投料方位問題。拌和混凝土所用的物料主要是砂石骨料、水泥、粉煤灰、水和外加劑等。質料水泥若包裹砂石遇水結塊，假如拌和不充沛就簡單粘在拌和軸上，若水泥進料口方位方向不合理，使拌和軸不能快速充沛拌和，就簡單構成抱軸現象。

2. It may be the material feeding direction. The materials used for mixing concrete are mainly sand and gravel aggregate, cement, fly ash, water and admixtures. If the wrapped sand and gravel of the material cement agglomerates with water, if the mixing is not sufficient, it will simply stick to the mixing shaft. If the orientation direction of the cement feed inlet is unreasonable, so that the mixing shaft can not be mixed quickly and sufficiently, it will simply form the phenomenon of shaft holding.

3.在結束作業之后沒有及時對拌和機內部進行清洗，或清洗不干凈，導致拌和軸外表仍有殘留的混凝土，枯燥后凝固在拌和軸上，假如長期如此則十分簡單發生抱軸現象。

3. After the operation is completed, the mixer is not cleaned in time, or the cleaning is not clean, resulting in the residual concrete on the surface of the mixing shaft, which is solidified on the mixing shaft after drying. If this is the case for a long time, the shaft holding phenomenon is very simple.

三.自動上料拌和機悶機跳閘原因分析

3、 Cause analysis of stuffy machine trip of automatic feeding mixer

1.投料過多，引起拌和機負荷過大。

1. Excessive feeding causes excessive load of mixer.

2.三角傳動皮帶太松，使傳動體系功率低。

2. The triangular drive belt is too loose, resulting in low power of the transmission system.

3.拌和主機上蓋安 全檢修開關被振松，引起停機。

3. The safety maintenance switch on the upper cover of the mixing machine was loosened, causing shutdown.

4.拌和體系葉片與襯板之間的空隙過大，拌和過程中，加大了阻力。

4. The gap between the blade and the lining plate of the mixing system is too large, which increases the resistance during the mixing process.