我們都知道不管是哪一種設備在安裝或者使用之前都會進行嘗試啟動運行這一環節，有利于我們提早發現問題不于影響到使用效果以及效率，自動上料攪拌車也是如此，那么該設備在安裝試車時應該注意什么呢？

　　We all know that no matter what kind of equipment will try to start the operation before installation or use, which is conducive to our early discovery of problems and will not affect the use effect and efficiency. The same is true for automatic feeding mixer. So what should we pay attention to when installing the equipment in the test run?

　　自動上料攪拌車設備應安裝在水平的混凝土基礎上，用地腳螺栓固定；安裝時應注意主機體與水平的垂直；安裝后檢查各部位螺栓有無松動及主機倉門是否緊固，如有請進行緊固；按設備的動力配置電源線和控制開關；檢查完畢，進行空負荷試車。

　　Automatic feeding mixer equipment should be installed on the level of concrete foundation, fixed with foot bolts; Installation should pay attention to the main body and horizontal vertical; After installation, check whether the bolts in each part are loose and whether the door of the main engine bin is fastened. If yes, please tighten it. Power line and control switch are configured according to the power of the equipment; After inspection, no-load test is carried out.

　　此外，機器的維護工作做的好會讓試車過程變得更加順利，操作人員所需要的做的事項包含：軸承擔負機器的全部負荷，所以良好的潤滑對軸承壽命有很大的關系，它直接影響到機器的使用壽命和運轉率，因而要求注入的潤滑油必須清潔，密封必須良好，；新安裝的輪箍容易發生松動必須經常進行檢查。

　　In addition, the maintenance of the machine work well done will make trial process more smoothly, operators need to do items include: all the load bearing for machine, so good lubrication for the bearing life has a great relationship, it directly affects the service life of machine and availability, and requirements into lubricating oil must be clean and seal must be good,; The newly installed wheel is easy to loose and must be checked frequently.

　　注意機器各部位的工作是否正常；注意檢查易磨損件的磨損程度，隨時注意更換被磨損的零件；放活動裝置的底架平面，應出去灰塵等物以免機器遇到不能破碎的物料時活動軸承不能在底架上移動，以致發生嚴重事故；軸承油溫升高，應立即停車檢查原因加以。；轉動齒輪在運轉時若有沖擊聲應立即停車檢查，并故障。

　　Pay attention to whether all parts of the machine work normally; Pay attention to check the wear degree of easy to wear parts, pay attention to replace worn parts at any time; Put the chassis plane of the mobile device, should be out of the dust and other things in order to avoid the machine can not be broken when the material movable bearing can not move on the chassis, resulting in a serious accident; Bearing oil temperature rise, should immediately stop to check the cause to eliminate. ; If there is a sound of impact when the rotating gear is running, it should be stopped immediately for inspection and fault elimination.

　　每次裝料前用水沖洗進料口，使進料口在裝料時保持濕潤；在裝料的同時向隨車自帶的清洗用水水箱中注滿水；裝料后沖洗進料口，洗凈進料口附近殘留的混凝土；在車輛回程時保持混凝土貯罐正向慢速轉動；下次裝料前切記放掉混凝土貯罐內的污水；每天收工時徹底清洗混凝土貯罐及進出料口周?chē)詣?dòng)。

　　Rinse the inlet with water before loading each time, so that the inlet is kept wet when loading; Fill the cleaning water tank with water when loading the material; After loading, wash the feed port and clean the residual concrete near the feed port; Keep the concrete storage tank moving slowly forward when the vehicle returns; Remember to discharge the sewage in the concrete storage tank before loading the next time; Every day at the end of the work thoroughly clean the concrete tank and material inlet and outlet around the automatic.

　　自動上料攪拌車的空負荷試車有多個注意事項的相關內容講解完畢，希望能夠帶給您幫助！當然如果您有什么問題要咨詢，可以點擊這里來網站kitchinit.com聯系我們的客服人員。

　　The empty load test of automatic feeding mixer has multiple matters needing attention. I hope to help you! Of course, if you have any questions to consult, you can click here to the website kitchinit.com to contact our customer service staff.