概述：全自動上料攪拌一體車的每個系統都是正常的，但無法啟動，是什么原因？接下來，教您診斷要點。
全自動上料攪拌一體車的每個系統都是正常的，但無法啟動，是什么原因？接下來，教您診斷要點。
Each system of the automatic feeding and mixing truck is normal, but it can not be started. What is the reason? Next, I will teach you the key points of diagnosis.
1.確定阻塞的原因。為了處理這種全自動上料攪拌一體車無法引發此類障礙的診斷，應測試電池。需要弄清楚電池電量是否不足。
1. Determine the cause of the blockage. In order to deal with the diagnosis that this kind of obstacle can not be caused by the automatic feeding and mixing vehicle, the battery should be tested first. We need to find out if the battery is low.
2.檢測啟動系統。在啟動系統中檢測電路。在基本配置方面，用于啟動系統的電路通常包括：電池，啟動器電動機和連接這些組件的電纜。此外，焚燒開關，起動繼電器或螺線管以及車載防盜系統也是啟動系統的重要組成部分。
2. Test the start-up system. Detect the circuit in the starting system. In terms of basic configuration, the circuits used to start the system usually include: battery, starter motor and cables connecting these components. In addition, incineration switch, starting relay or solenoid and vehicle anti-theft system are also important parts of the starting system.
3.焚燒同步帶的檢測出現打滑現象，不會產生火花，這也是無法啟動的原因。
3. The detection of the incineration synchronous belt has the phenomenon of slipping, and there will be no spark, which is also the reason why it can not be started.
4.檢測火花的質量?？梢匀∠路倩€圈，并可以使用電火花探測器檢測火花是否正常。
4. Check the quality of spark. The incineration coil can be removed and the spark detector can be used to detect whether the spark is normal.
5.檢測燃油系統。其燃油系統的診斷可分為兩部分：燃油供給系統的診斷和噴射器回路的診斷。燃料供應系統可以通過測量燃料的流量和壓力進行檢測。測量燃油流量的一個好方法是在燃油供應管路中加載負載來測試管路。
5. Check the fuel system. The diagnosis of fuel system can be divided into two parts: diagnosis of fuel supply system and diagnosis of injector circuit. The fuel supply system can be detected by measuring the flow and pressure of the fuel. A good way to measure fuel flow is to test the line by loading the fuel supply line.
6.防盜系統的檢測：其防盜系統也會發生一些經常被忽視的供油系統。一些全自動上料攪拌一體車制造商在防盜系統的數據流中包含參數標識。在許多型號上，防盜系統的模塊未經適當?shù)某跏蓟幚砭捅桓摹?/div>
6. Detection of anti-theft system: the anti-theft system will also have some oil supply system which is often ignored. Some manufacturers of fully automatic feeding and mixing vehicles include parameter identification in the data stream of anti-theft system. On many models, the anti-theft system module has been changed without proper initialization.
The above is the problem that the fully automatic feeding and mixing vehicle can not start the diagnosis method. Of course, other aspects not mentioned will also affect it. I hope the above contents can provide reference for you.
點擊撥打服務熱線：400-879-1999
