自動上料攪拌車是現在比較常用的大型運輸車輛，它工作效率高，運輸速度快，因此攪拌車的輪胎充氣是很重要的，下面就說說輪胎充氣注意事項。

Automatic loading mixer truck is a commonly used large-scale transportation vehicle now. It has high working efficiency and fast transportation speed. Therefore, tire inflation of mixer truck is very important. Here are the precautions for tire inflation.

1、攪拌車充氣不要選擇剛剛行駛過的時候進行充氣，要等輪胎完全冷卻后再充氣，因為長時間行駛過的車輛輪胎溫度較高，我們知道熱脹冷縮原理，輪胎溫度過高對氣壓是有一定的影響的，所以為了正確的判斷氣壓情況，我們需要等輪胎溫度冷卻后再進行充氣。

1. Don't choose to inflate the mixer when it has just been driven. Wait until the tires are completely cooled before inflating. Because the tires of vehicles that have been driven for a long time have a high temperature, we know the principle of thermal expansion and cold contraction. Too high tire temperature has a certain impact on the air pressure, so in order to correctly judge the air pressure, we need to wait until the tire temperature is cooled before inflating.

2、在輪胎充氣前我們需要檢查充氣是否清潔，如果充氣設備或周圍環境不清潔，很容易有水分、油污、雜質等進入輪胎內，造成內胎橡膠變形變質或出現早期損壞現象。還有就是注意氣門嘴的清潔，輪胎長期與地面接觸，氣門嘴上往往有泥土、灰塵等，在充氣前我們需要將氣門嘴清理趕緊，以防止雜質進入輪胎內，損壞輪胎。

2. Before inflation, we need to check whether the inflation is clean. If the inflation equipment or the surrounding environment is not clean, it is easy for moisture, oil, impurities, etc. to enter the tire, causing deformation and deterioration of the inner tube rubber or early damage. Also, pay attention to the cleaning of the valve. The tire is in long-term contact with the ground, and there are often mud, dust, etc. on the valve. Before inflation, we need to clean the valve quickly to prevent impurities from entering the tire and damaging the tire.

3、充氣時盡量不要松動或取出自動上料攪拌車的氣門芯，靠增大氣壓強行充氣，以防造成氣門嘴螺絲脫扣漏氣。充氣完畢后，應蘸水涂在氣門嘴上，檢查是否漏氣，以便視情況擰緊或更換氣門芯。充完氣，還應配齊裝緊氣門嘴帽，防止泥沙等進入氣門嘴內。

3. When inflating, try not to loosen or take out the valve core of the automatic feeding mixer truck, and forcibly inflate by increasing the air pressure to prevent the valve screw from tripping and air leakage. After inflation, dip water on the valve to check whether there is air leakage, so as to tighten or replace the valve core according to the situation. After gas filling, the valve cap should also be fully installed to prevent sediment from entering the valve.

要注意：

Note:

隨著攪拌車成本的不斷增加，攪拌車輪胎實際上成本很高，其驅動方式與輪胎磨損有很大的關系。良好而熟練的駕駛技術可以 減少攪拌車輪胎的磨損，延長輪胎使用壽命，提高駕駛 。我們無法控制價錢 ，因此如何減少磨損，保護輪胎使用周期更大 化是我們需要掌握的。

With the increasing cost of mixer truck, the cost of mixer truck tire is actually very high, and its driving mode has a great relationship with tire wear. Good and skilled driving skills can reduce the wear of mixer tires, prolong the service life of tires and improve driving. We can't control the price, so we need to know how to reduce wear and protect the tire's service life.

，胎壓應達到標準。攪拌車駕駛員應按照要求給輪胎充氣。當輪胎壓力低于標準值時，輪胎胎肩磨損會增加。當輪胎壓力高于標準值時，由于輪胎的接地面積減小，單位壓力增大，從而使輪胎的中間磨損增加，同時，輪胎的剛度增加，并且車輪動負荷增大，胎體容易發生爆裂。

First, the tire pressure should meet the standard. The mixer driver shall inflate the tires as required. When the tire pressure is lower than the standard value, the tire shoulder wear will increase. When the tire pressure is higher than the standard value, because the grounding area of the tire decreases and the unit pressure increases, the middle wear of the tire increases. At the same time, the stiffness of the tire increases, and the dynamic load of the wheel increases, and the tire body is prone to burst.

此外在駕駛攪拌車時要注意，在夏季或高速行駛時，輪胎很容易過熱，而壓力卻增加了。這時，駕駛員應停車以散熱，嚴禁放氣或水冷，以防止橡膠異常老化，造成損害。更多事項就來我們網站http://kitchinit.com咨詢吧。

In addition, when driving a mixer truck, it should be noted that in summer or when driving at high speed, the tires are easy to overheat, but the pressure increases. At this time, the driver should stop to dissipate heat, and it is strictly forbidden to deflate or water-cooling, so as to prevent abnormal aging of rubber and damage. Come to our website for more information http://kitchinit.com Consult.