自上料攪拌車有時候會出現問題，是由于里面有很多的土渣沒有清理干凈，需要及時將內部的土渣清理出來，這樣才能使它正常運行，接下來就教大家清理土渣的方法，希望能夠給您幫助。

Sometimes there are problems with the self loading mixer, because there are a lot of soil residues in it that have not been cleaned. It is necessary to clean out the internal soil residues in time so that it can operate normally. Next, I will teach you how to clean the soil residues. I hope I can help you.

1、準備好緊急驅動軟管，將自上料攪拌車熄火，卸下液壓馬達上的高壓油管接頭。

1. Prepare the emergency drive hose, turn off the self feeding mixer, and remove the high-pressure oil pipe connector on the hydraulic motor.

2、將救援車熄火，將其液壓馬達的高壓油管卸下，并與故障車上的對應接頭用緊急驅動軟管相連。

2. Turn off the rescue vehicle, remove the high-pressure oil pipe of its hydraulic motor, and connect it with the corresponding connector on the failed vehicle with the emergency drive hose.

3、發動救援車，將其操縱手柄撥至出料位置，故障車內的混凝土即被排出。

3. Start the rescue vehicle and turn its operating handle to the discharging position, and the concrete in the fault vehicle will be discharged.

4、緊急驅動完畢后，將驅動軟管卸下，并恢復兩車原狀。

4. After the emergency drive is completed, remove the drive hose and restore the two vehicles to their original state.

5、還有一種簡單點的方法就是在托輪和滾道之間放入木楔，控制攪拌筒的旋轉，將發動機熄火，拆松液壓馬達的一根高壓油管，攪拌筒可自由旋轉，控制攪拌筒的旋轉，使維修孔轉到下部，然后打開維修孔，清理出筒內混凝土?；炷僚懦鐾戤吅?，恢復攪拌車原狀。

5. Another simple method is to put a wooden wedge between the supporting wheel and the raceway, control the rotation of the mixing drum, turn off the engine, and loosen a high-pressure oil pipe of the hydraulic motor. The mixing drum can rotate freely, control the rotation of the mixing drum, turn the maintenance hole to the lower part, and then drill the maintenance hole to clean the concrete in the drum. After the concrete is discharged, the mixer shall be restored to its original state.

自上料攪拌車的清洗過程：

Cleaning process of self feeding mixer:

1、每天的工作結束后，將攪拌罐內注入適量的水，并保持攪拌罐緩慢旋轉；

1. After daily work, inject proper amount of water into the mixing tank and keep the mixing tank rotating slowly;

2、將自上料攪拌車水箱里的水加滿，以保證清洗過程的水量充足；

2. Fill up the water in the water tank of the loading mixer to ensure sufficient water in the cleaning process;

3、向罐體內注水，注水過程中保持攪拌罐工作狀態，以足夠的水量保證洗掉攪拌罐內殘存的混凝土；

3. Inject water into the tank, keep the mixing tank in working condition during the water injection, and ensure that the residual concrete in the mixing tank is washed off with sufficient water;

4、打開洗車泵，接好高壓水槍（高端自上料攪拌車標配，有些廠家可能需要定制）；

4. Turn on the car washing pump and connect the high-pressure water gun (standard for high-end self feeding mixer, some manufacturers may need to customize);

5、仔細清洗罐體、進料口、出料口、車身等殘留物料；

5. Carefully clean the residual materials such as tank body, feed port, discharge port and vehicle body;

6、確認沒有水泥和混凝土結塊后，將攪拌罐內污水放掉。

6. After confirming that there is no cement and concrete caking, drain the sewage in the mixing tank.

以上就是自上料攪拌車清洗土渣的方法，無論是選擇哪種方法都要注意安全，當然平日使用中的維護保養事項是不能少的，您可以來我們網站http://kitchinit.com進行詳情了解。

The above is the method of cleaning soil slag by self loading mixer. No matter which method you choose, you should pay attention to safety. Of course, the maintenance items in daily use are indispensable. You can visit our website http://kitchinit.com For details.