How should we pay attention to the wear of parts of the 4-way automatic feeding mixer? Let's have a look.

1.維持自動送料混合器設備的額定負載

1. maintain rated load of automatic feeding mixer equipment

像這樣的工程機械的負載性質和尺寸對設備部件的損失具有重要影響。當零件的載荷高于設計時，一般機械零件的磨損會隨著載荷的增加而增加。當施加工作載荷時，其部件的磨損將繼續增加。

The load properties and dimensions of such construction machinery have important influence on the loss of equipment components. When the load of parts is higher than the design, the wear of general mechanical parts increases with the increase of load. When the working load is applied, the wear of its components will continue to increase.

2.及時清潔，以減少機械雜質對設備的影響

2. clean in time to reduce the influence of mechanical impurities on the equipment

機械雜質通常指的是施工機械本身在使用過程中產生的灰塵，污垢和其他材料以及一些金屬碎屑和油漬。一旦這些雜質到達機器的工作表面之間，危險就很大：不僅摩擦增加，而且燃料消耗也增加。它還會破壞潤滑油膜并刮擦配合表面。

Mechanical impurities usually refer to dust, dirt and other materials produced by construction machinery itself during the use process, as well as some metal debris and oil stains. Once these impurities reach the working surface of the machine, the danger is great: not only friction increases, but also fuel consumption. It also destroys the lubricant film and scrapes the mating surface.

3.防止4方自動上料攪拌車部件腐蝕

3. prevent the corrosion of parts of the 4-way automatic feeding mixer

腐蝕作用于零件，有時不容易被發現，很容易被忽視，而且更有害。雨水，空氣中的化學物質等通過機械部件的管道，狹縫等滲入機器，并腐蝕部件。腐蝕部件的持續工作也會加速機器的磨損并增加機械故障。這要求管理人員和操作人員根據當?shù)氐漠?dāng)?shù)靥鞖鈼l件和現場條件采取合理的施工安排，盡量減少對機械部件的化學腐蝕損害。

Corrosion acts on parts, sometimes not easily found, easily ignored, and more harmful. Rainwater, chemicals in the air, etc. penetrate the machine through the pipes and slits of mechanical parts, and corrode the parts. The continuous operation of corrosive parts also accelerates the wear of the machine and increases the mechanical failure. This requires management and operators to take reasonable construction arrangements according to local local weather conditions and site conditions, and minimize chemical corrosion damage to mechanical parts.

4.保持4方自動上料攪拌車部件的合理溫度

4. keep the reasonable temperature of the parts of the 4-way automatic feeding mixer

在工作中，每個組件的溫度都有其自己的正常范圍。溫度過高或過低都會影響零件的強度，因此必須用冷卻液和潤滑油控制某些零件的溫度，使其在合理的溫度范圍內工作。

In operation, the temperature of each component has its own normal range. Too high or too low temperature will affect the strength of parts, so the temperature of some parts must be controlled with coolant and lubricating oil to work within a reasonable temperature range.

4方自動上料攪拌車

4-way automatic feeding mixer

4方自動上料攪拌車的剎車技巧

The brake technique of the 4-way automatic feeding mixer

一是下坡剎車

First, the downhill brake

首先按下擠壓尾部系統，然后擠壓前部系統，目的是防止汽車前部下沉過多，并積極增加尾輪的重量，以免壓在桅桿上。

First press the extrusion tail system, then the front system, in order to prevent the front of the car from sinking too much, and actively increase the weight of the tail wheel to avoid being pressed on the mast.

二，使用腳趾和腳底之間的力來踩剎車。

Second, use the force between the toe and the foot to apply the brake.

使用腳趾制動器不如使用腳底快。它可以瞬間將整個制動踏板推到最后，以最大化制動能力。從人們通常操作制動器的方式可以看出駕駛水平。當按下制動器時，汽車立即停止，或者當汽車停止時，它不能停止。這不是駕駛大師的表現。

Using toe brake is not as fast as using the sole of the foot. It can momentarily push the entire brake pedal to the end to maximize the braking capacity. The driving level can be seen from the way people normally operate the brakes. When the brake is pressed, the car stops immediately or it cannot stop when the vehicle stops. It's not a driver's performance.

三，乘客制動穩定

Third, the passenger braking is stable

當后座上有乘客時，汽車頭部和尾部的重量相對平均，但隨著汽車重量的增加，慣性也增加，并且所需的制動力大大提高。當增加制動器時，后座乘客可能會撞到椅子上，因?yàn)樗麄儧]有準備好保護。只要您教導坐著的乘客坐下，您就可以解決它們。

When there are passengers in the back seat, the weight of the head and tail of the car is relatively average, but with the increase of the vehicle weight, the inertia increases, and the braking force required is greatly improved. When the brakes are added, the rear seat passengers may hit the chair because they are not ready to protect. You can solve them as long as you teach the seated passengers to sit down.

4方自動上料攪拌車的剎車技巧以及減少零件磨損的方法就在這里了，希望對你有幫助。

The brake skills of the 4-way automatic feeding mixer and the method of reducing the wear of parts are here. I hope it will help you.