There are many places that are easy to be ignored in the maintenance of automatic feeding mixer. Let's take a look at the aspects below.

一、二者之間的自鎖系數變小、自鎖性能下降。在攪拌車高速行駛時，螺栓螺母很容易松動乃至脫落，從而引發行車事故。不要用水沖洗車身，因?yàn)橄奶鞖鉁馗?，很多司機選擇用水沖洗車身，在拿干凈的抹布擦拭，但其實車身內部是不能用水來沖洗的。因?yàn)轳{駛室內地板膠墊的下面可不是“一馬平川”，結構上的需要使駕駛室地板膠墊下面的凹槽、通孔很多。

1、 The self-locking coefficient becomes smaller and the self-locking performance decreases. When the mixer is running at high speed, the bolts and nuts are easy to loose or even fall off, which leads to traffic accidents. Don't wash the car body with water. Because of the high temperature in summer, many drivers choose to wash the car body with water and wipe it with a clean cloth. However, the interior of the car body can't be washed with water. Because the bottom of the floor mat in the cab is not flat, there are many grooves and through holes under the floor mat in the cab due to the need of structure.

用水沖洗后，要么沉積在凹槽內不易干燥，要么從通孔處流到變速箱等部件上產生銹蝕。尤其是密封性能較好的轎車不能用水直接沖洗車身內部。

After washing with water, either it is deposited in the groove and not easy to dry, or it flows from the through hole to the gearbox and other parts to produce corrosion. Especially for cars with good sealing performance, the interior of the car body cannot be washed directly with water.

正確的方法是用濕抹布擦拭，但要避免積水。不同的冷卻液不要混合使用不同的冷卻液其化學性能可能相差懸殊，比如對黑色金屬有用的防腐劑，卻常常對鋁制品有腐蝕作用;而適用于鋁臺金的防腐劑則對鐵合金有害。由于不同的冷卻液所用的防腐劑不同，所以不能混合使用。

The correct method is to use a wet cloth to wipe, but to avoid water. Do not mix different coolants. The chemical properties of different coolants may vary greatly. For example, preservatives are useful for ferrous metals, but they often corrode aluminum products; However, the preservatives suitable for aluminum alloy are harmful to ferroalloy. Due to the different preservatives used in different coolant, it can not be mixed.

二、啟動時不要踩油門：?jiǎn)?dòng)攪拌車發動機前踩幾腳油門，是許多攪拌車駕駛員的習慣，尤其是在冬季冷車啟動時。裝有電控噴油裝置的攪拌車發動機與普通化油器式發動機不同，它的噴油控制裝置能根據攪拌車發動機的溫度、工況自動調整供油量，使攪拌車發動機順利啟動，即在冷車啟動時，噴油控制裝置能自動增加供油量。所以，攪拌車發動機啟動時，沒有必要踩油門，更不要在啟動前連續急踩，否則反而使攪拌車發動機啟動不好。

2、 Don't step on the accelerator when starting: it's the habit of many mixer drivers to step on the accelerator before starting the mixer engine, especially when it's cold in winter. The mixer engine equipped with electronic control fuel injection device is different from the ordinary carburetor engine. Its fuel injection control device can automatically adjust the fuel supply amount according to the temperature and working condition of the mixer engine, so that the mixer engine can start smoothly. That is to say, the fuel injection control device can automatically increase the fuel supply amount during the cold start. Therefore, there is no need to step on the accelerator when the mixer engine starts, let alone continuously step on it before starting, otherwise, the mixer engine will not start well.

三、不要給自動上料攪拌車的輪胎螺栓螺母涂油在車輪維修中，少數司機為了防止攪拌車的車輪上螺栓螺母生銹，安裝時別出心裁地將螺栓螺母都涂上潤滑油，殊不知這種做法不僅錯誤，而且給攪拌車行車安全帶來的隱患。螺栓和螺母擰緊后，相互間具有自鎖的特性。

3、 Don't oil the wheel bolts and nuts of the automatic feeding mixer. In wheel maintenance, in order to prevent the wheel bolts and nuts of the mixer from rusting, a few drivers apply lubricating oil on the bolts and nuts with ingenuity during installation. However, this practice is not only wrong, but also brings hidden danger to the driving safety of the mixer. After the bolt and nut are tightened, they are self-locking.