RM新时代入口

歡迎來到中科聚峰機械有限公司!

24小時服務熱線:

400-879-1999

點擊撥打服務熱線:400-879-1999
當前位置:首頁>新聞中心>常見問題自動上料攪拌車作業中出現土渣問題

自動上料攪拌車作業中出現土渣問題

來源:http://kitchinit.com/ 日期:2022-04-20 發布人:admin
概述:  自動上料攪拌車作業中會出現各式各樣的問題,全看操作人員要如何去解決,不及時解決就會出現大的損失。那么自動上料攪拌車作業中出現土
  自動上料攪拌車作業中會出現各式各樣的問題,全看操作人員要如何去解決,不及時解決就會出現大的損失。那么自動上料攪拌車作業中出現土渣問題怎么處理?
  There will be all kinds of problems in the operation of automatic feeding mixer. It all depends on how the operator wants to solve them. If they are not solved in time, there will be big losses. So how to deal with the problem of soil slag in the operation of automatic feeding mixer?
  首先應準備好緊急驅動軟管,將機械熄火,卸下液壓馬達上的高壓油管接頭。將救援車熄火,將液壓馬達的高壓油管拆卸,并與故障車上的相應接頭利用緊急驅動軟管相連接。
  First, prepare the emergency drive hose, turn off the machine, and remove the high-pressure tubing joint on the hydraulic motor. Turn off the rescue vehicle, remove the high-pressure oil pipe of the hydraulic motor, and connect it with the corresponding joint of the faulty vehicle using the emergency drive hose.
  發動救援車并將操作手柄撥動至出料位置,故障車中的混合便會被排出。當緊急驅動完成后,將自動上料攪拌車中的驅動軟管拆卸,并回復至原狀。在拖輪、滾道間放入木楔,并控制攪拌筒的旋轉,將發動機熄火,將液壓馬達的一根高壓油管拆卸。
  Start the rescue vehicle and move the operating handle to the discharging position, and the mixture in the failure vehicle will be discharged. When the emergency drive is complete, remove the drive hose from the automatic feeding mixer and return it to its original state. Put wooden wedges between tugboats and raceways, and control the rotation of the mixing cylinder, turn off the engine, and remove a high-pressure oil pipe of the hydraulic motor.
  攪拌筒可自由旋轉并控制攪拌筒的旋轉。從而讓維修孔轉到下部位置,然后將維修孔打開,并清理出筒中的混凝土,當混凝土排出完成后,恢復自動上料攪拌車的原來狀態即可。
  The agitator can rotate freely and control the rotation of the agitator. So that the maintenance hole to the lower position, and then open the maintenance hole, and clean up the concrete in the cylinder, when the concrete discharge is complete, restore the original state of the automatic feeding mixer.
  在檢查、修理攪拌車液壓傳動部分時,應使發動機和液壓泵在沒有壓力的情況下進行。在調整混凝土攪拌車各部間隙、行程、壓力時,應由專職安全員檢查同意;更換機件時,須由部長或主管經理簽字,否則出現問題后追究有關人員責任。
  When inspecting and repairing the hydraulic transmission part of the agitator, the engine and hydraulic pump should be carried out without pressure. When adjusting the clearance, stroke and pressure of each part of the concrete mixing truck, the full-time safety officer should check and agree; When replacing parts, it must be signed by the minister or the manager in charge, otherwise the relevant personnel will be held responsible after problems occur.
  自動上料攪拌車作業中出現土渣問題要怎么處理?以上的方法希望能夠給您幫助,當然要想攪拌車長久的運行就要做好日常保養工作哦。更多內容就來網站kitchinit.com咨詢吧!
  How to deal with the problem of soil slag in the operation of automatic feeding agitator? The above methods hope to help you. Of course, if you want to run the mixer for a long time, you must do a good job in daily maintenance work. More content to the website kitchinit.com consultation!

截屏,微信識別二維碼

RM新时代入口