攪拌一體機它是行業中使用很廣泛的，攪拌一體機有時受到淡季的影響，會閑置一段時間，那么攪拌一體機閑置時怎么保養呢？如何預防攪拌一體機事故發生呢？下面工作人員就向大家介紹下：

The all-in-one mixer is widely used in the industry. Sometimes it is affected by the off-season and will be idle for a period of time. How to maintain the all-in-one mixer when it is idle? How to prevent mixing machine accidents? The following staff will introduce to you:

1.防變形

1. Anti deformation

攪拌一體機的彈簧、傳動帶、桿、輪胎等零件由于長期受力或放置不當會產生塑性變形，為此應在機架下面加以適當?shù)闹?，使輪胎不承受?fù)載，飼料攪拌機上的所有壓緊或拉開的彈簧須放松。拆下傳動帶在室內妥善保管，有些拆下的易變形零件如桿要放平或垂直掛起，另外拆下的零件如輪胎、輸種管等保管時要防止擠壓變形。

The spring, transmission belt, rod, tire and other parts of the mixing machine will produce plastic deformation due to long-term stress or improper placement. Therefore, proper support should be provided under the frame to make the tire not bear the load. All compressed or pulled springs on the feed mixer must be loosened. The removed drive belt shall be properly kept indoors. Some easily deformed parts, such as rods, shall be placed flat or hung vertically. In addition, the removed parts, such as tires and seed delivery pipes, shall be protected from crushing deformation.

2.防銹蝕

2. Rust prevention

攪拌一體機機作業完畢后，須清除外部泥垢，清理工作機構內的飼料、雜物，必要時用水或油清洗。清洗各潤滑部位，并重新進行潤滑，對所有摩擦工作面，如犁鏵、犁壁、開溝器、鋤鏟等須擦凈后涂機油，貼紙，以減少與空氣接觸氧化的機會。

After the operation of the mixing machine is completed, the external dirt must be removed, the feed and sundries in the working mechanism must be cleaned, and if necessary, water or oil must be used for cleaning. Clean all lubricating parts and re lubricate them. Clean all friction working surfaces, such as ploughshare, plough wall, furrow opener, hoe and shovel, and then apply oil and stickers to reduce the opportunity of air contact oxidation.

復雜精密的機具放在陰涼、干燥、通風的室內保管，等簡單機具，可以露天保管，但要放在地勢較高、干燥、不受陽光直射的地方，能搭棚遮蓋，凡與地面直接接觸的零件，應用木板或磚支起，脫落的防護漆要重新涂好。

Complex and precise machines and tools can be stored in a cool, dry and ventilated room, and simple machines and tools can be stored in the open air, but they should be placed in a higher, dry place that is not exposed to direct sunlight and can be covered by a shed. All parts that directly contact the ground should be supported by wood or bricks, and the fallen protective paint should be repainted.

3.防腐朽

3. Anti corrosion

霉?fàn)€木制的零件由于受微生物的作用以及雨淋、風吹、日曬而腐朽、和變形，有效的保管方法是在木料外表涂上油漆，置于干燥的地方，不要受到日曬、雨淋，這類制品不應在露天放置，應該拆下清洗曬干后，存放在室內干燥和能防蟲、防鼠害的地方。

Moulded wooden parts are subject to decay and deformation due to the effect of microorganisms, rain, wind and sun. The effective storage method is to paint the surface of the wood and place it in a dry place. It should not be exposed to sun and rain. Such products should not be placed in the open air. They should be removed, cleaned and dried, and stored indoors in a dry place that can prevent insects and rats.

對長期停放的攪拌一體機應詳細記載機具的技術狀態、附屬裝置、備件、工具等，各種機具應由專人保管，嚴禁拆卸零件作其他用，如沒有庫房，機具在室外停放時，應將電動機、傳動帶等易丟件拆下來并作好標記，存放在室內。關注我們網站http://kitchinit.com了解更多的詳細內容！

For the mixing machine that has been parked for a long time, the technical status, accessory devices, spare parts, tools, etc. of the machines and tools shall be recorded in detail. All machines and tools shall be kept by a specially assigned person. It is strictly prohibited to remove parts for other purposes. If there is no warehouse, when the machines and tools are parked outdoors, the easily lost parts such as motors, transmission belts, etc. shall be removed, marked, and stored indoors. Follow our website http://kitchinit.com Learn more!