1.它由動力輸出裝置，萬向軸，液壓泵，液壓馬達，控制閥，液壓油箱和冷卻系統組成普通車削零件是有缺陷的零件。潤滑脂應按時加注，應經常檢查磨損并及時修理和更換。團隊必須有一個備用的萬向軸組件，以便萬一發生故障，幾分鐘之內即可將其恢復。

1. It consists of power take-off, cardan shaft, hydraulic pump, hydraulic motor, control valve, hydraulic oil tank and cooling system. Ordinary turning parts are defective parts. The grease should be filled on time, the wear should be checked frequently, and the grease should be repaired and replaced in time. The team must have a spare cardan shaft assembly so that it can be restored in a few minutes in case of failure.

2.確保液壓油清潔?；炷翑嚢柢?chē)的工作環境不好，必須防止臟的水泥砂進入液壓系統。應根據手冊的要求定期更換液壓油。如果檢查發現液壓油被水或沙子污染，則應立即停止液壓系統并更換液壓油。

2. Make sure the hydraulic oil is clean. The working environment of concrete mixer is not good, so it is necessary to prevent the dirty cement sand from entering the hydraulic system. The hydraulic oil should be changed regularly according to the manual. If it is found that the hydraulic oil is polluted by water or sand, stop the hydraulic system immediately and replace the hydraulic oil.

3.確保啟用了液壓油冷卻器。定期清潔液壓散熱器，以防止其被水泥堵塞，并確保散熱器風扇正常工作，并且液壓溫度不超過正常溫度。只要保證液壓部件能夠清潔液壓油，通常故障很少，但是制造商具有不同的使用壽命。

3. Make sure that the hydraulic oil cooler is activated. Regularly clean the hydraulic radiator to prevent it from being blocked by cement, and ensure that the radiator fan works normally, and the hydraulic temperature does not exceed the normal temperature. As long as the hydraulic components can clean the hydraulic oil, there are usually few failures, but the manufacturers have different service life.

九、攪拌和卸載

Mixing and unloading

雙錐形滾筒擁有雙螺旋形攪拌螺桿和中凸底部。

The biconical drum has a double spiral stirring screw and a convex bottom.

滾筒幾何容量：.................... 5000L

Geometric capacity of drum: 5000L

滾筒旋轉速度：..................20轉/分鐘.

Drum rotation speed: 20 rpm

混凝土產量：.................3.2立方米/罐

Concrete output: 3.2m3/can

“重型”球形鞍座上安裝的反力架可以180°液壓旋轉，并且通過液壓式制動器自動鎖止。滾筒

 

旋轉通過柱塞泵和閉路中的柱塞液壓馬達實現，在操作室內和攪拌機后部擁有手動電氣閥。

The reaction frame installed on the "heavy" spherical saddle can rotate 180 ° hydraulically and lock automatically by hydraulic brake. The rotation of the drum is realized by the plunger pump and the plunger hydraulic motor in the closed circuit. There are manual electric valves in the operation room and at the rear of the mixer.

可拆卸溜槽可以保證直接通過料斗卸載。作為標準配置提供1個溜槽延長部件。

The detachable chute can ensure direct unloading through the hopper. A chute extension is provided as standard.

設備液壓系統

Equipment hydraulic system

齒輪泵：雙聯齒輪泵

Gear pump: double gear pump

大流量：.................... 90升/分鐘。

Maximum flow rate: 90 L / min.

大壓力：........................ 27.5MPa兆帕，

Maximum pressure: 27.5mpa, MPa,

馬達：企業/ 美國桑尼

Motor: brand / Sonny

3件手柄多功能操縱桿。

Three handle multi-function control lever.

鋁質熱交換器，用于冷卻液壓油。

Aluminum heat exchanger for cooling hydraulic oil.

半閉式進油，可以從外部更換液壓油過濾器。

Semi closed oil inlet, hydraulic oil filter can be changed from outside.

裝載

load

裝載臂配置自動稱量感應儀，雙作用裝載裝置舉升和復位油缸，手動控制的進料口擁有標準的提示功能。

The loading arm is equipped with automatic weighing sensor, double acting loading device, lifting and reset oil cylinder, and the manually controlled feeding port has standard prompt function.

容量：.............................. 700升

Capacity: 700 liters

每次裝滿需要的裝載次數：.......... 大約5次

Loading times required for each filling:...... about 5 times