If there is a problem with the automatic feeding mixer, and the cause of the failure can not be found, it will have a bad impact on the direction booster pump, and more likely, it will be damaged.

自動上料攪拌車轉向助力泵，我們通常把它叫做方向機助力泵，它是清障車轉向助力系統的動力源，也是轉向系統的心臟部分。對于重型清障車來說，由于機械式方向機，駕駛員操作勞動強度大，所以液壓轉向系統就更為重要。

Automatic feeding mixer power steering pump, we usually call it steering power pump, it is the power source of the steering system of the wrecker, but also the heart of the steering system. For heavy-duty obstacle removal vehicles, due to the mechanical steering gear, the driver's labor intensity, so the hydraulic steering system is more important.

一般的葉片泵是由一個內腔雙圓弧曲線的泵體帶槽轉子.葉片等零件組成。有的安裝在發動機后端的飛輪殼上，也是靠正時齒輪驅動。當發動機運轉時，帶動助力泵轉子轉動，葉片在離心力的作用下，沿葉片槽向外移動，緊靠泵體的內壁，在轉子轉動過程中，由于葉片間封閉的容積不斷的增加和減小實現了吸油和壓油的過程。

The general vane pump is composed of a pump body with double circular arc curve and grooved rotor and blade. Some of them are installed on the flywheel housing at the rear end of the engine and are driven by timing gears. When the engine is running, it drives the rotor of the booster pump to rotate. Under the action of centrifugal force, the blade moves outward along the blade groove and is close to the inner wall of the pump body. In the process of rotor rotation, due to the continuous increase and decrease of the closed volume between the blades, the process of oil absorption and oil pressure is realized.

轉子每轉一周，完成吸油和壓油二次。在泵體內還有安全閥以限制最高壓力。當轉向系外部負荷增加，導致油壓升高到一定數值時，安全閥開啟卸掉負荷。泵體內還安裝有節流閥和流量控制閥，以保證助力泵的排量基本上處于穩定性。

Every rotation of the rotor, complete oil suction and oil pressure twice. There is also a relief valve in the pump body to limit the maximum pressure. When the external load of the steering system increases and the oil pressure rises to a certain value, the safety valve opens to unload the load. The throttle valve and flow control valve are also installed in the pump body to ensure that the displacement of the booster pump is basically stable.

方向機助力泵的使用與維護尤為重要，因此，必須做到以下幾點：

The use and maintenance of steering gear booster pump is particularly important. Therefore, the following points must be done:

一、在使用中如發現方向機助力泵滲漏，沖擊或有異常的噪音，應及時檢查排除。

1、 If leakage, impact or abnormal noise are found in the use of the steering gear booster pump, timely check and eliminate.

二、自動上料攪拌車運行一段時間后，應及時更換液壓油幾濾芯，尤其是新泵裝車后使用2500-3000公里應更換液壓油。

2、 After the automatic feeding mixer runs for a period of time, several filter elements of hydraulic oil should be replaced in time, especially when the new pump is used 2500-3000 km after loading.

自動上料攪拌車

Automatic feeding mixer

三、定期檢查儲油罐的油平面，不足應及時補充清潔的液壓油，儲油罐內的濾芯應在保養時用酒精清洗干凈。

3、 Check the oil level of the oil tank regularly. If it is insufficient, clean hydraulic oil should be added in time. The filter element in the oil tank should be cleaned with alcohol during maintenance.

四、正確選擇液壓油是保證助力泵高效率，延長壽命的關鍵。

4、 The correct selection of hydraulic oil is the key to ensure high efficiency and prolong service life of booster pump.

我們應該如何進行換油呢？方法如下：

How should we change the oil? The method is as follows:

支起前橋，使車輪離地。拆下儲油罐蓋，拆下回油管及方向機放油螺塞。啟動發動機高速運轉10分鐘左右，使儲油罐，方向機助力泵，方向機內的液壓油排出。發動機熄火，左右轉動方向盤至極限位置，把殘余的液壓油全部排出。更換濾芯，加液壓油至規定的高度，排凈液壓系統的空氣。

Support the front axle so that the wheels are off the ground. Remove the oil tank cover, oil return pipe and oil drain plug of steering gear. Start the engine to run at high speed for about 10 minutes, so that the oil tank, steering gear booster pump and hydraulic oil in the steering gear are discharged. Turn the steering wheel left and right to the limit position to drain the residual hydraulic oil. Replace the filter element, add hydraulic oil to the specified height, and exhaust the air in the hydraulic system.

以上就是自動上料攪拌車方向機助力泵的有關知識，想要了解更多請關注我們的網站。

The above is about the knowledge about the power pump of the direction machine of the automatic feeding mixer. If you want to know more, please pay attention to our website.