When driving the automatic feeding mixer, it is inevitable to encounter problems. If it is difficult to start, what is the reason for this problem?

1、如果啟動時只有輕微“嗒”的一聲，之后就再?zèng)]有任何反應時，就可以是啟動繼電器發卡出了問題。

1. If there is only a slight "click" sound when starting, and then there is no response, it can be that the starting relay is jammed.

2、當啟動時只聽到啟動機電磁開關發出“咯咯”聲，但曲軸卻不轉動。那就有可能是蓄電池“斷格”造成的。

2. When starting, only the electromagnetic switch of the starter makes a "cluck" sound, but the crankshaft does not rotate. That may be caused by the battery "broken grid".

3、當極樁、極樁夾子接觸不良而發熱燒損，您啟動時會發現啟動機突然轉動無力，并伴有燒橡膠氣味或蓄電池處冒煙。

3. When the pole post and pole post clamp are burned due to poor contact, you will find that the starter suddenly turns weakly, accompanied by the smell of burning rubber or smoke from the battery.

4、當飛輪齒圈的嚙合切入面變形的時候，就會出現啟動時啟動機驅動齒輪與發動機飛輪齒圈會發出撞擊的空轉聲。

4. When the meshing cutting surface of the flywheel ring gear is deformed, the idling sound of the impact between the starter drive gear and the engine flywheel ring gear will appear.

5、當蓄電池自放電嚴重，其極板、隔板嚴重老化時，就會出現臨時停車每次都能啟動，但停車時間較長或第二天啟動時卻只能使曲軸轉一下。那個時候您可以考慮更換蓄電池。

5. When the battery self discharge is serious, and its plate and partition board are seriously aging, it will appear temporary stop, and it can start every time, but it can only make the crankshaft turn once for a long time or the next day. At that time, you can consider replacing the battery.

6、當啟動機電磁開關的保持線圈錯接在了電源接線柱上或鑰匙開關上的3根線接錯時，電源總開關一接通，就會出現混凝土攪拌車啟動機驅動齒輪就和飛輪齒圈嚙合在一起轉動的現象。

6. When the holding coil of the electromagnetic switch of the starter is wrongly connected to the power terminal or the three wires of the key switch are wrongly connected, as soon as the main power switch is connected, the phenomenon that the driving gear of the starter of the concrete mixer will mesh with the flywheel ring gear will appear.