The automatic feeding mixer engine is playing a key role in the whole control application process, and many friends are familiar with many shortcomings of the automatic feeding mixer engine. Therefore, many troubles of the automatic feeding mixer machine are formed by our own shortcomings. Accurate maintenance and familiarity have a good effect on the application life of the vehicle.

一些自動上料攪拌車駕駛員認為發動機溫度居下沒有低,所以自發撤除發動機恒溫器,冷卻液只能除夜周期,不克不及調解冷卻強度,所以發動機經常正在高溫條件下工作,導致權利的損失,磨損,燃料消費增加,等等。事實上,高溫對發動機有害。應該正在一樣平常溫度限定自動上料攪拌車的應用范例,以確保發動機的應用壽命。

Some auto feeding mixer drivers think that the engine temperature is not low, so they remove the engine thermostat spontaneously. The coolant can only adjust the cooling cycle, but can not adjust the cooling intensity. Therefore, the engine is often working under high temperature conditions, resulting in the loss of rights, wear loss, increased fuel consumption, and so on. In fact, high temperature is harmful to the engine. Should be the same as the usual temperature limit automatic feeding mixer application example, in order to ensure the service life of the engine.

帶松沒有是更好。皮帶太松不只會讓它舒展或損壞,收縮皮帶的應用壽命,并且借由于壓力太除夜,導致自動上料攪拌車發電機軸,泵軸曲折變形戰軸承初期損傷。寬松的自動上料攪拌車發動機電扇皮帶應相符技巧要求,一樣平常一樣平常帶裝配偏差10到15毫米為宜。

It's better not to have loose belts. Too loose belt will not only make it stretch or damage, shrink the service life of the belt, but also lead to automatic feeding mixer generator shaft, pump shaft bending deformation and bearing initial damage due to too much pressure. Loose automatic feeding mixer engine fan belt should meet the technical requirements, as usual with assembly deviation of 10 to 15 mm is appropriate.

很多司機曉得,車子方才開端,如果發動機轉速過下會損害發動機由于滑膩不良。但是,很少有人曉得如果應用閑置很少一段時間升溫,由于低速，自動上料攪拌車油泵不克不及迅速按下潤滑油為全體滑膩表面,發動機全體挪動部件將正在干摩擦或半干摩擦條件下工作。

Many drivers know that the car has just started, if the engine speed is too low, it will damage the engine due to poor lubrication. However, few people know that if the application is idle for a short period of time, due to the low speed, the automatic feeding mixer oil pump cannot quickly press the lubricating oil to all the greasy surfaces, and all the moving parts of the engine will be working under dry friction or semi dry friction conditions.

同時由于高溫燃油霧化沒有良,使已燃燒的燃料進入曲軸箱,洗失落氣缸壁的油膜,加速零件磨損。是以,正在高溫條件下,自動上料攪拌車發動機啟動幾秒鐘后,應該改良怠速疾速加熱,提高發動機滑膩條件。

At the same time, due to the poor atomization of high-temperature fuel, the burned fuel enters the crankcase and washes out the oil film on the cylinder wall, which accelerates the wear of parts. Therefore, under the high temperature condition, after the automatic feeding mixer engine starts for a few seconds, it should improve the idling speed heating to improve the engine greasy condition.