RM新时代入口

歡迎來到中科聚峰機械有限公司!

24小時服務熱線:

400-879-1999

點擊撥打服務熱線:400-879-1999
當前位置:首頁>新聞中心>行業新聞6方自上料攪拌車噪音大溫度高的問題是什么原因引起的?

6方自上料攪拌車噪音大溫度高的問題是什么原因引起的?

來源:http://kitchinit.com/ 日期:2021-04-19 發布人:admin
概述:夏天很熱,6方自上料攪拌車的內部噪音很高,溫度也很高。夏季的低溫可能是由于發動機和機油的溫度所致。
夏天很熱,6方自上料攪拌車的內部噪音很高,溫度也很高。夏季的低溫可能是由于發動機和機油的溫度所致。
It's very hot in summer. The internal noise and temperature of 6-square self feeding mixer are very high. The low temperature in summer may be caused by the temperature of engine and oil.
1.洗車池中的水量不足。加水到洗車池。
1. There is not enough water in the car wash pool. Add water to the car wash.
2.如果吸管的吸口被阻塞或堵塞,則可以檢查并擰緊吸管。
2. If the suction port of the straw is blocked or blocked, check and tighten the straw.
3.如果燃油箱中的油位過低并且油位中的空氣已泵入泵中,則可以添加具有相同標簽的液壓油。
3. If the oil level in the fuel tank is too low and the air in the oil level has been pumped into the pump, the hydraulic oil with the same label can be added.
4.如果泵安裝支架的剛性不足,并且在工作過程中發生振動或噪音,則可以加固油泵安裝支架。
4. If the rigidity of the pump mounting bracket is insufficient, and vibration or noise occurs in the working process, the pump mounting bracket can be reinforced.
5.如果濾芯堵塞,則可能很難或不可能完全吸收機油。在這種情況下,可以清潔或更換濾芯。
5. If the filter element is blocked, it may be difficult or impossible to completely absorb the oil. In this case, the filter element can be cleaned or replaced.
6.油冷卻風扇未打開。解決方案:打開冷卻風扇。
6. The oil cooling fan is not turned on. Solution: turn on the cooling fan.
7.如果液壓油不符合要求或油的粘度太高,請更換符合標簽要求的低粘度液壓油。
7. If the hydraulic oil does not meet the requirements or the viscosity of the oil is too high, please replace the low viscosity hydraulic oil that meets the label requirements.
8.儲罐中有堅硬的混凝土。如果發生這種情況,請及時清理并鏟起。
8. There is hard concrete in the tank. If this happens, clean up and shovel in time.
9.如果輸入法蘭與萬向傳動軸之間的連接角度以及萬向傳動軸與取力器之間的連接角度太大,則松動時會產生噪音。如果發生這種情況,請及時檢查并擰緊。
9. If the connection angle between the input flange and the cardan drive shaft and the connection angle between the cardan drive shaft and the power take-off are too large, noise will be generated when it is loose. If this happens, please check and tighten in time.
6方自上料攪拌車溫度高引起的原因你都了解了嗎?更多精彩內容直接關注:http://kitchinit.com
Do you understand the causes of high temperature in 6-way self feeding mixer? Direct attention to more highlights: http://kitchinit.com

截屏,微信識別二維碼

RM新时代入口