Cement, fly ash, mineral powder and other powder materials are usually used to produce concrete. Most of these powder materials are stored in the cement silo of automatic mixer truck, which is rainproof and moisture-proof. Generally, when purchasing mixing plant facilities, it is equipped with automatic mixer, and a reasonable number of cement silos are matched with your production needs.

日常使用的自動攪拌車水泥倉也比較簡單，但在使用過程中，生產的影響是材料的管理，如材料過多，過少，導致材料破裂或缺乏。因此，典型水泥筒倉中更重要的部件是液位計。水泥倉用于避免爆炸和材料短缺。

Daily use of automatic mixer cement silo is also relatively simple, but in the process of use, the impact of production is the management of materials, such as too much or too little material, resulting in material rupture or lack. Therefore, the more important component in a typical cement silo is the level gauge. Cement silo is used to avoid explosion and material shortage.

自動攪拌車的水泥倉液位計大多采用開關式液位計，安裝在水泥筒倉的底部。它具有結構合理，性能可靠，安裝簡單，性價比高的特點。簡單地說，當粉末倉中的材料位置低于設定的下限或負荷高于設定的上限時，將發出警報信號以提示操作者執行相應的處理。

The liquid level meter of cement silo of automatic mixer mostly adopts switch type liquid level meter, which is installed at the bottom of cement silo. It has the characteristics of reasonable structure, reliable performance, simple installation and high cost performance. In short, when the material position in the powder bin is lower than the set lower limit or the load is higher than the set upper limit, an alarm signal will be issued to prompt the operator to carry out the corresponding processing.

水泥倉液位計的工作原理如下：

The working principle of liquid level gauge in cement silo is as follows:

AC微電機在減速后驅動葉片旋轉或振蕩。當檢測到的材料上升到葉片的位置時，葉片作用被阻擋，并且檢測機構的主軸產生旋轉位移。該位移首先產生微動開關動作，輸出切換信號，然后另一個微動開關操作以切斷電動機的電源以停止操作。只要倉庫中的物料級別保持不變，此狀態將繼續。

The AC micromotor drives the blades to rotate or oscillate after deceleration. When the detected material rises to the position of the blade, the effect of the blade is blocked, and the spindle of the detection mechanism generates rotation displacement. The displacement first generates a micro switch action, outputs a switching signal, and then another micro switch operates to cut off the power supply of the motor to stop the operation. This status will continue as long as the item level in the warehouse remains unchanged.

當材料降低時，葉片阻力消失，測量裝置通過彈簧的張力返回到原始狀態，并且控制電動機電源的微動開關以打開電動機并旋轉。隨后，另一個微動開關操作以輸出切換信號，只要沒有材料阻擋檢測葉片的旋轉，該切換信號將保持不變。彈簧的張力可以根據不同比重的材料進行調節。當比率大時，彈簧的張力可以非常強烈地調節，反之亦然。

When the material is reduced, the blade resistance disappears, the measuring device returns to the original state through the spring tension, and controls the micro switch of the motor power supply to turn on the motor and rotate. Then, another micro switch operates to output a switching signal, which will remain unchanged as long as there is no material blocking the rotation of the detection blade. The tension of the spring can be adjusted according to the material with different specific gravity. When the ratio is large, the spring tension can be adjusted very strongly, and vice versa.