概述: 用戶反映自己的自動上料攪拌車使用中會出現漏油的情況,事實上如果不及時處理漏油問題,那么很有可能會引起機件早期損壞,所以今天我們
用戶反映自己的自動上料攪拌車使用中會出現漏油的情況,事實上如果不及時處理漏油問題,那么很有可能會引起機件早期損壞,所以今天我們先來查找下漏油原因,以便能夠做好應對措施。
Some users report that there will be oil leakage in the use of their automatic feeding mixer. In fact, if the oil leakage problem is not dealt with in time, it is likely to cause early damage to parts, so today we will first find the cause of oil leakage, so as to be able to do a good job in responding to measures.
自動上料攪拌機上的各種螺母是否擰緊。有時,自動上料攪拌機的漏油是因?yàn)檐囕v的連接螺母松動。
All nuts on automatic feeding mixer are tight. Sometimes oil leaks from automatic feeder mixers are caused by loose coupling nuts on vehicles.
Oil leakage of automatic feeding mixer may also be the cause of excessive wear, aging, deformation and failure of sealing materials after long-term use.
擰緊螺母的擰緊力不均、滑動螺紋斷裂或松動脫落也會導致工作失敗。如果墊片太松而未擰緊,墊片會泄漏;如果擰得太緊,螺絲孔附近的金屬會突出或螺紋扭曲而導致漏油。
Uneven tightening force of tightening nut, fracture or loose falling off of sliding thread will also lead to work failure. If the gasket is too loose and not tightened, the gasket will leak; If the screw is tightened too tightly, metal near the screw hole can protrude or twist the thread, causing oil leakage.
裝配是否不當,表面是否不干凈,墊片是否損壞、移位或未按操作規程安裝。更換聯管螺母,用磨削法解決錐面密封,壓緊螺母解決密封。如果材料、生產質量和安裝不符合技術規范,將無法密封和防止泄漏,甚至?xí)l(fā)生事故。
Whether the assembly is improper, whether the surface is not clean, whether the gasket is damaged, displaced or not installed according to the operating procedure. Replace the union nut, solve the cone sealing with grinding method, and solve the sealing by pressing the nut. If the material, production quality and installation do not meet the technical specifications, it will not be able to seal and prevent leakage, and even accidents will occur.
是否是輪轂油。結果,套管內溫度升高,油氣充滿整個空間而無法排出,使套管內壓力增加,潤滑油消耗量增加,更換周期縮短。
Is it hub oil? As a result, the temperature in the casing rises and the oil and gas fill the space without being discharged, increasing the pressure in the casing, increasing the consumption of lubricating oil and shortening the replacement cycle.
自動上料攪拌機上的許多運動部件會因安裝不當而產生錯位。輪轂軸承和腔內潤滑脂過多,或油品包裝不當,質量差,老化失效;頻繁制動導致輪轂溫度過高;軸螺母松動等會導致輪轂甩油,漏油應及時更新。
Many moving parts on the automatic feeding mixer may be misplaced due to improper installation. Hub bearing and grease in the cavity is too much, or oil packaging is improper, poor quality, aging failure; Frequent braking results in high hub temperature; Axle nut loosening will lead to hub oil dumping, oil leakage should be updated in time.
在這里我們排查了幾個方面的漏油原因,當然如果您在使用自動上料攪拌車工作時還發生了別的問題而您找不到原因時,歡迎隨時來
http://kitchinit.com網站咨詢!