攪拌一體車作為一種建設機械產品，對于提高施工效率，降低成本起著很大的作用，但是在施工過程中要注意正確操作，下面是攪拌一體車的操作流程：

As a construction mechanical product, the mixer truck plays a very important role in improving construction efficiency and reducing costs. However, attention should be paid to correct operation during construction. The following is the operation process of the mixer truck:

1、停車

1. Parking

將攪拌一體車行駛停放到工作區，拉好手剎將檔位撥至空擋熄火，注意要將泵車停在泵送臂架工作范圍內。

Drive the mixer truck and park it in the working area. Pull the hand brake and turn the gear to neutral to stop the engine. Pay attention to parking the pump truck within the working range of the pumping arm.

2、轉換發動機工作狀態

2. Switch the engine working state

將電控箱操作面板上的行車開關轉換至泵送位置，啟動底盤發動機，將底盤檔位掛到6檔，同時檢查攪拌機電箱、支腿與臂架轉換位置、主電控箱、泵車無線遙控器和攪拌機有線遙控的急停開關是否有打開。

Switch the traveling switch on the operation panel of the electric control box to the pumping position, start the chassis engine, shift the chassis gear to gear 6, and check whether the emergency stop switches of the agitator box, outrigger and boom switch positions, the main electric control box, the wireless remote control of the pump truck and the wired remote control of the mixer are turned on.

3、伸展支腿

3. Stretch outriggers

將臂架支腿轉換開關切換到支腿位置，依次將六條泵機支腿展開。注意將支腿下方墊木方，這樣是用支承板或輔助方木來增大支承表面積，從而保持整車的平衡。

Switch the boom outrigger change-over switch to the outrigger position, and unfold the six pump outriggers in turn. Pay attention to cushion the wooden square under the outrigger. In this way, the bearing plate or auxiliary square timber is used to increase the bearing surface area, so as to maintain the balance of the whole vehicle.

4、伸展臂架

4. Extension boom

將臂架支腿轉換開關切換到臂架位置，將大臂伸開。

Switch the boom outrigger change-over switch to the boom position and extend the boom.

5、支撐攪拌機

5. Support mixer

拔出攪拌機定位銷，將攪拌機推動到工作位置，插好定位銷。放下上料斗上下滑道，連接好固定螺栓。

Pull out the positioning pin of the mixer, push the mixer to the working position, and insert the positioning pin. Lower the upper and lower slides of the upper hopper and connect the fixing bolts.

6、啟動發電機

6. Start generator

啟動時要注意看發電機組空氣開關是否處于斷開狀態，不能帶負荷啟動，以免影響發電機消磁。

When starting, pay attention to whether the air switch of the generator set is in the off state, and do not start with load to avoid affecting the degaussing of the generator.

7、開始泵送

7. Start pumping

將混凝土原料放入泵車料斗，等待混凝土攪拌好后，將攪拌好的混凝土放入料斗連續泵送。

Put the concrete raw materials into the hopper of the pump truck, wait for the concrete to be mixed, and then put the mixed concrete into the hopper for continuous pumping.

8、清洗

8. Cleaning

泵送完畢后，要對攪拌一體車進行清洗，先清洗干凈料斗內的混凝土，然后沖洗料斗。

After pumping, the mixer truck shall be cleaned. First, the concrete in the hopper shall be cleaned, and then the hopper shall be washed.

9、關閉發電機組

9. Shut down the generator set

斷開空氣開關，將發電機組柴油機轉速降至低速運轉30秒后關閉發電機組。

Disconnect the air switch, reduce the speed of the diesel engine of the generator set to low speed for 30 seconds, and then shut down the generator set.

10、收車

10. Collection

將攪拌一體車收到行車狀態，插好定位銷，依次收好臂架和支腿，將底盤檔位撥至空擋，將轉換開關切換行車狀態。

After receiving the driving status of the mixer truck, insert the positioning pin, put the boom and outrigger in order, shift the chassis gear to neutral, and switch the change-over switch to the driving status.

攪拌一體車屬于特種工程機械，作業前一定要經過培訓考核合格才能操作。畢竟安全為重，不能大意，您有什么問題就來我們網站http://kitchinit.com咨詢吧！

The mixer truck belongs to special construction machinery, and must pass the training and examination before operation. After all, safety is the most important thing. Don't be careless. Come to our website if you have any problems http://kitchinit.com Consult!