自動上料攪拌車的防護一般指?jìng)?cè)防護和后防護，具體要求您知道有什么內容嗎？下面就來為您講解一番。

The protection of automatic feeding mixer generally refers to side protection and rear protection. Do you know the specific requirements? Now let's explain it for you.

側防護

Side protection

1.側防護橫桿截面積100*30mm

1. The sectional area of the side protective cross bar is 100*30mm

2.2個橫桿間距不超過300mm，建議控制在200~250mm

2. The spacing between two cross bars shall not exceed 300mm, and it is recommended to control it within 200~250mm

3.下面的橫桿下邊緣離地高度≤550mm（以空載后橋那邊高度為準），建議離地高度500mm

3. The height from the lower edge of the lower cross bar to the ground ≤ 550mm (subject to the height of the unloaded rear axle), and the recommended height from the ground is 500mm

4.上面的橫桿距離車身≤350mm，如果是罐式車等兩邊沒有板的車，側防護上面橫桿的上邊緣要距離地面950mm以上。

4. The distance between the upper cross bar and the vehicle body is ≤ 350mm. If there is no plate on both sides, such as a tank car, the upper edge of the cross bar on the side protection should be more than 950mm from the ground.

5.側防護前側做成弧面，弧面的半徑為100mm的四分之一圓?。▓A弧周長628mm，四分之一就是157mm，可以做大，不能做?。髠?cè)封口

5. The front side of the side protection is made into an arc surface, and the radius of the arc surface is a quarter arc of 100mm (the circumference of the arc is 628mm, and the quarter is 157mm, which can be made larger, not smaller), and the rear side is sealed

6.前側和后側距離輪胎都不超過300mm，建議控制在250mm以?xún)?nèi)

6. The distance between the front and rear sides of the tire shall not exceed 300mm, and it is recommended to control it within 250mm

7.豎桿底部加焊斜支撐到副梁上

7. The bottom of the vertical bar is welded to the auxiliary beam

8.測防護第一個站樁距離第一個封口不超過200mm

8. The distance between the first station pile and the first seal shall not exceed 200mm

9.側防護距離能替代側防護的東西，比如空氣濾芯器的距離控制在25毫米以?xún)?nèi)

9. The side protection distance can replace the side protection. For example, the distance of air filter element is controlled within 25mm

后防護

Rear protection

1.后防護需要承受總質量乘以50%的壓力不變形，N2類需要100mm高，N3類需要120mm高，需要使用6mm厚的矩形管，截面積為120*50mm

1. The rear protection needs to bear the pressure multiplied by 50% of the total mass without deformation. Category N2 needs to be 100mm high, category N3 needs to be 120mm high, and a 6mm thick rectangular tube with a cross-sectional area of 120*50mm needs to be used

2.橫桿下邊緣離地高度≤500mm

2. The height from the lower edge of the cross bar to the ground ≤ 500mm

3.橫桿的左右長度，長為后橋輪胎外邊緣的長度，短為后橋輪胎外邊緣減100mm

3. The left and right length of the crossbar is the length of the outer edge of the rear axle tire, and the short is the length of the outer edge of the rear axle tire minus 100mm

4.橫桿兩端往內側傾斜，邊緣封口

4. Both ends of the cross bar are inclined to the inside, and the edge is sealed

5.橫桿與連接件之間需要做四個斜支撐

5. Four diagonal supports are required between the cross bar and the connector

不管你購買的車是自動上料攪拌車還是隨車吊還是清障車，它的側防護和后防護尺寸必須符合以上要求，各位卡友可以根據這些對自己的愛車做一下檢測，看是否符合要求。

No matter whether the car you buy is an automatic loading mixer, an on-board crane or a wrecker, its side protection and rear protection dimensions must meet the above requirements. Card friends can test their cars to see whether they meet the requirements.

以上就是今天為大家介紹的關于問題以及注意事項的全部?jī)?nèi)容，希望對大家能有所幫助，想要了解更多內容可以電話聯系我們或者關注我們的網站http://kitchinit.com，我們的工作人員會及時與您取得聯系。

The above is all about the problems and precautions introduced to you today. I hope it can help you. If you want to know more, you can contact us by phone or follow our website http://kitchinit.com , our staff will contact you in time.